Thursday, March 25, 2010

HELP on DSTV Signal Issues

What could cause a failure or interruption to your DStv reception?

Signal Issues

What could cause a failure or interruption to your DStv reception?

Quality of picture and sound

MultiChoice has operates a 24-hour monitoring room which tracks the channel signals on all satellites. Should you have any problems relating to the broadcast, they should be infrequent and quickly resolved.

Dish size

MultiChoice recommends that only 90cm dishes are used within the footprints from the IS-7 (Formerly PAS 7), W4 and SESAT satellites. Any dish smaller than this will cause failures or interruptions to your television signal. In areas that experience seasonal bad weather, sometimes a larger dish size (120 cm+) is recommended.

Installations

For best results please ensure you use an accredited MultiChoice installerto connect you DStv. An updated list of accredited installers can be obtained from your nearest MultiChoice office or in the Agents and Installers section of this site.

Power failure

Frequent power failures are experienced in some countries. We recommend you use a surge protector to protect against decoder box failures.

Surge Protectors

A power surge, or transient voltage, is a sudden increase in voltage, which is significantly above the designated level in an electrical circuit. In most countries, the main power supply operates at 220V. This voltage is available in normal households and offices.

Under normal conditions i.e., in the absence of an electrical failure, this voltage produces a nominal current which operates electronic devices. If this voltage rises above the values tolerated by the devices connected to it, there may be damage caused by the excess current. A surge protector absorbs the excess current generated in such cases, and thus avoids damages to electronic devices. For this reason, MultiChoice recommends the use of surge protectors to protect decoders' and avoid damage.

Dirty dish

Ensure that your satellite dish is clean as the accumulation of dust and dirt on the dish will negatively affect your signal.

Solar Outages

During certain times in the year, the satellite communication industry around the world experiences transmission disruptions. This occurs when the sun crosses the equator and traces an arc that places it directly behind Geostationary satellites. This phenomenon is known as a solar or sun outage and will last several minutes each day during the season and will last longer, the smaller the antenna involved satellite dish is in use.

The event may occur for several days both before and after the peak day, at roughly the same time each day.

Rain Fade

Rain fade (temporary loss of signal) usually only occurs in during very heavy rain and bad weather and should only last for a few seconds. We estimate that only about 0.1% of annual viewing time is lost as a result of rain interference, which affects all satellite systems worldwide. You should not experience any problems with your signal if the sky is overcast of or if there is drizzle or normal rainfall.

If you experience rain fade for longer than 1 to 2 seconds, you may have an installation problem. It is preferable to contact a MultiChoice Accredited Installer to check any installation related problem - you may, however, check the following yourself:

The position of your dish. to check that your dish is firmly anchored and has not been disturbed / moved in the bad weather. Contact an installer to rectify the problem.

The GT number on your Low Noise Block Down-Converter (the LNB is the small box on the arm of your satellite dish). The GT number should be 17 or higher to guarantee good reception. Adjustment of the GT number may only be performed by an accredited installer.

It is important to bear in mind that the signal can also be affected by adverse local weather conditions in the location from which the signal is broadcast. For example bad weather in Randburg (South Africa) or Spain, from where we uplink (broadcast the signal to the satellite), may affect the clarity of the signal.

Troubleshooting - Error Codes

Below is a list of all our error codes.

E04 - Please insert Smartcard

Your smartcard might have been inserted incorrectly or in the incorrect slot. Remove the Smartcard, wipe with a soft dry cloth and re-insert. If message re-appears, reboot. If problem persists then the decoder and/or the Smartcard might be damaged and must be tested.

E05 - Unknown Card

The incorrect Smartcard is inserted or the Smartcard might have been inserted incorrectly or has collected dust. Remove the Smartcard, ensure that it is free of dust and re-insert it with the chip facing downwards and the arrows facing the decoder. Reboot the decoder.

E07 - Checking Smartcard

The decoder is checking the Smartcard. If the message is still displayed after 30 seconds remove the Smartcard, wait for the error code and re-insert the Smartcard. If

E07 reappears, reboot your decoder. If E07 reappears, the decoder/Smartcard might be damaged and should be brought in for testing.

E08 – CA Module failure

The Control Access module is malfunctioning. Please have your decoder tested.

E14 – Service is Currently Scrambled

Transmission might be temporarily suspended. Tune to another channel and back again. If the message re-appears, re-boot your decoder. If the E14 message re-appears again, contact your nearest MultiChoice Contact Centre.

The code E37 error appears on all the channels.

Your decoder might be in the incorrect bouquet selection. Press the TV button on the remote control, scroll up to 'DStv bouquet' and press the OK button.

E16 – Service is currently scrambled

Transmission might be temporarily suspended. Check that there are no outstanding payments on your account. The service needs to be reset from by MultiChoice. Call your local MultiChoice Contact Centre

E17 – Service is currently scrambled

Transmission has been scrambled. Re-boot your decoder. If the error code re-appears call your local MultiChoice Contact Centre .

E18 – Unknown Smartcard

The incorrect Smartcard is inserted or the Smartcard might have been inserted incorrectly or has collected dust. Remove the Smartcard, ensure that it is free of dust and re-insert it with the chip facing downwards and the arrows facing the decoder. Re-boot the decoder.

E19 – Service is currently Scrambled

Your subscription might have expired. Please call your nearest MultiChoice Contact Centre.

E30 – Service is currently scrambled

Transmission might be temporarily suspended. Check that there are no outstanding payments on your account. The service needs to be re-set fromby MultiChoice. Call you local MultiChoice Contact Centre.

E32 – Service is currently scrambled

Your Smartcard is not switched on or activated. Check that there are no outstanding payments on your account. The service needs to be reset from MultiChoice. Call you local MultiChoice Contact Centre.

E34 – Service is currently scrambled

The signal is not being received. Tune to another channel and back again. If the problem persists, re-boot the decoder.

E35 – Service is currently scrambled

Temporary failure in receiving transmission .Tune to another channel and back again. If the problem persists, re-boot your decoder.

E37 – Service XX is reserved for future use

There is no service running on the selected channel number. An incorrect channel number was entered. Re-enter the required channel number.

E38 – Service is not currently running

The service is not running. Consult the TV Guide Dish or TV Guide for running hours of this service.

This service might be reserved for future use. If the error appears often, re-boot the decoder. If the problem persists, your decoder might be faulty and should be tested.

E39 – Locating Service

The decoder is trying to locate the service. Wait a couple of seconds until the service is located.

E42 – Parental Control Lock

The service/event has been blocked by parental control. Enter your PIN to cancel the parental control block or call your nearest MultiChoice Contact Centre if you have forgotten your PIN.

E45 – Searching for signal at XXXX MHz

The satellite dish is not receiving a signal. This might be caused by bad weather – either where you live or where the signal originates from (Randburg, UK etc). Your installation may, however, might need checking if the message persists.

Mobile Phone Tips

If you are a DStv subscriber and you receive the E16 error message on your TV even after you have paid your DStv subscription; you need not panic. Simply follow the steps below using your mobile phone to reset your decoder.

To clear an E16 error message after your account has reconnected, text RA and the first 10 digits of your smartcard to 08036393788

To retrieve your smartcard number text SC to 08036393788

To retrieve your Account Balance text BAL to 08036393788

To retrieve your due date text DD to 08036393788

To use the self help option using your mobile phone, please ensure that your mobile number is registered on our system.

To register your mobile phone number, send an email to: dstv@nigeria.multichoice.co.za or call the call centre numbers: 01-2703232, 08039003788 with the mobile number(s) you wish to use and it will be registered.

56 comments:

  1. Hi

    Hope you can help me. Will a tree make the DSTV signal weaker and must I use a certain LNB for an Explora?

    Regards
    Anton

    ReplyDelete
  2. Decoder is blank will not switch on

    ReplyDelete
  3. Decoder is blank will not switch on

    ReplyDelete
  4. Decoder is blank will not switch on

    ReplyDelete
  5. Hi I cannot get the signal, the lnb is new a twin lnb connections are also correct, dish position and lnb alignment is correct, dish in a position where it was for the past4 years but cannot get signal even with the use of satellite finder. Kindly help

    ReplyDelete
  6. No signal and decoder has the orange light on and the green light keeps blinking

    ReplyDelete
    Replies
    1. Same problem here, any solutions

      Delete
    2. Same problem I even changed power cable but with no luck

      Delete
  7. How is it possible some of my channels are working fine but others are jumping from 0%-81% signal strength? I don't understand this, unless this is a ploy for us to upgrade to the explorer!.......

    ReplyDelete
  8. Hi my name is Jolene our dstv explo
    ra keeps rebooting every 5minutes its the secondary decoder the primary decoder works fine. Must add this is the 3rd decoder in 3 months please help what can i do? Signal fine just keeps rebooting ...

    ReplyDelete
  9. Hi my name is Jolene our dstv explo
    ra keeps rebooting every 5minutes its the secondary decoder the primary decoder works fine. Must add this is the 3rd decoder in 3 months please help what can i do? Signal fine just keeps rebooting ...

    ReplyDelete
  10. Hi my name is Jolene our dstv explo
    ra keeps rebooting every 5minutes its the secondary decoder the primary decoder works fine. Must add this is the 3rd decoder in 3 months please help what can i do? Signal fine just keeps rebooting ...

    ReplyDelete
  11. My dstv can not pick up signal what can I do

    ReplyDelete
  12. My dstv can not pick up signal what can I do

    ReplyDelete
  13. My decoder didn't work and I got a new power unit from DSTV which works and shows a red and green light. However I am still not getting any channels? Can anyone help me please?

    ReplyDelete
  14. The decoder scans but number of operators remains zero.what might be the problem?

    ReplyDelete
  15. The decoder scans but number of operators remains zero.what might be the problem?

    ReplyDelete
  16. Good evening to everyone my problem is that the signal is lost and the massage promised me that I must Wait 10 seconds after that it does the same plz help

    ReplyDelete
    Replies
    1. Hi I have the same problem... Could you fix yours? If so how did you go about it?

      Delete
    2. Hi I have the same problem... Could you fix yours? If so how did you go about it?

      Delete
    3. Hi I have the same problem... Could you fix yours? If so how did you go about it?

      Delete
  17. HD 4S no signal decoder problem. What might be the problem?

    ReplyDelete
  18. Pls help me..I get a massage that says I should check the LNB cable so u don't know what to do cause there's no signal...its been searching for hours now

    ReplyDelete
  19. My dstv just went to no signal while we watching n it said do not switch if off,but if it continues call the help line,we waited for hours,it kept on searching until we switched it off,since from 8:50am still searching

    ReplyDelete
  20. My dstv just went to no signal while we watching n it said do not switch if off,but if it continues call the help line,we waited for hours,it kept on searching until we switched it off,since from 8:50am still searching

    ReplyDelete
  21. No signal red light keeps on blinking and orange light no blue light

    ReplyDelete
    Replies
    1. Orange light on no green light decode don't work

      Delete
  22. Only red light with an envelope underneath showing. Cant change channels nor resert

    ReplyDelete
  23. No more error codes and troubles while subscribing, paying and renewing your DStv plan with https://www.vtpass.com/dstv

    ReplyDelete
  24. Good day,I have a 4u hd decoder and don't have signal,I unplugged the decoder,remove smartcard but still no signal,please help

    ReplyDelete
  25. Good day,I have a 4u hd decoder and don't have signal,I unplugged the decoder,remove smartcard but still no signal,please help

    ReplyDelete
  26. Hy help my Dstv say pg blocked help plz

    ReplyDelete
  27. Hy help my Dstv say pg blocked help plz

    ReplyDelete
  28. I've been having problem with dstv I only have 5 channels playing the rest says error I've called them but it seems to be of no help it's been 5 days now need help

    ReplyDelete
  29. I've been having problem with dstv I only have 5 channels playing the rest says error I've called them but it seems to be of no help it's been 5 days now need help

    ReplyDelete
  30. My dstv decoder lights is going crazy and it show there is no signal. What can i do?

    ReplyDelete
  31. My decoder doesn't have signal E48-32

    ReplyDelete
  32. My decoder shows notification E52-32 frequently, how can I fix it?

    ReplyDelete
  33. My decoder shows notification E52-32 frequently, how can I fix it?

    ReplyDelete
  34. My decoder shows no signal,how can i fix it?

    ReplyDelete
    Replies
    1. My decoder shows no signal for 2 days now how can I fix it

      Delete
  35. The decoder it's blinking with yellow, green and red lights without showing any pics its being 3 day now can someone help please.

    ReplyDelete
  36. My dstv is not operating due to error ff:there is no signal.Plz help

    ReplyDelete
  37. My primary decoder keeps scaning but secondary works fine. Is it a faulty lnb?

    ReplyDelete
  38. my decorder shows three colours red and green are bipping orange is stable please help

    ReplyDelete
  39. My decoder has gone into wizard mode I cannot scan my decoder to play channels .its completey off .it signal is totally lost any solutions cause I ended up switching it off nd wiping the sdcard then re enserfing it .

    ReplyDelete
  40. What must I do my dstv lost signal it do not play since today morning

    ReplyDelete
  41. My dstv has problem blinking non stop then no signal play black and white no clear colours 8704106336083

    ReplyDelete
  42. Can some one help me my decoder is blinking red orange n green pictures please help

    ReplyDelete
  43. I have a Model 4s, I Done a Factory Reset and now it says (Please ensure signal strength or quality is high enough). The Dish and LNB is working fine. I have a Satellite Finder. There are no Error Codes. Thank you.

    ReplyDelete
  44. Also, you can check out this website for some help on DSTV error codes - https://tvandvideodoctor.co.za/dstv-message-error-codes-e48-32-e143-4

    ReplyDelete
  45. DSTV Signal Problems Services in South Africa
    https://www.dstvinstallerssa.co.za/dstv-installation-in-south-africa/
    Get the best DSTV installation services in South Africa. We provide the best CCTV installation and DSTV signal problems services in South Africa. Call us now - 063 519 9882

    ReplyDelete